BJJB-300B金屬半自動沖擊試驗機
一、設備名稱：金屬半自動沖擊試驗機
二、型 號：BJJB-300B
三、性能說明：
BJJB-300B沖擊試驗機用于測定金屬材料在動負荷下抵抗沖擊的性能，從而判斷材料在動負荷作用下的質量狀況。
本機為半自動控制試驗機，操作簡單工作效率高，揚擺、沖擊、放擺電器控制，并能利用沖斷試樣后的剩余能量自動揚擺作好下次試驗準備，特別適用于連續做沖擊試驗的實驗室和大量做沖擊試驗的冶金、機械制造等行業。
BJJB-300B型沖擊試驗機符合國標GB/T3808-2002《擺錘式?jīng)_擊試驗機的檢驗》，按國標GB/T229-2007《金屬材料夏比擺錘沖擊試驗方法》對金屬材料進行沖擊試驗。
四、技術特點：
1、試驗機主機為單支承柱式結構，懸臂式掛擺方式，擺錘錘體U型；
2、沖擊刀采用螺釘安裝固定，更換簡單方便；
3、試樣簡支梁式支承；
4、主機裝有安全防護銷，并且配備了安全防護網；
5、試驗機為半自動控制，揚擺、掛擺、沖擊、放擺均為電氣控制，并能利用沖斷試樣后的剩余能量自動揚擺做好下次試驗準備，特別適用于連續做沖擊試驗的試驗室和大量做沖擊試驗的冶金、機械制造等部門；
6、試驗機符合國標GB/T3803-2002《擺錘式?jīng)_擊試驗機的檢驗》，按國標GB/T229-2007《金屬夏比缺口沖擊試驗方法》對金屬材料進行沖擊試驗。
五、技術指標：
1、沖擊能量：300J（大錘） 150（小錘）
2、沖擊速度：5.2m/s
3、擺錘預揚角：150°
4、試樣支座跨距：40mm
5、支座鉗口圓角：R1.0~1.5mm
6、沖擊刀刃圓角：R2.0~2.5mm R8mm
7、擺錘中心至沖擊點距離：750mm
8、標準試樣尺寸：10×10(7.5或5)×55mm
9、擺錘力矩： M=160.7695N.m 80.3848N.m
10、電源和功率：三相四線 50Hz 380V 180W
11、外形尺寸：約2100×650×1900mm
12、角度準確度： 0.1°
13、重量： 約500Kg
六、設備主要配置：
1、300焦耳主機 1臺
2、150J、300J 擺錘各 1個
3、電機（裝在主機上）； 1臺
4、內六角扳手S=12（扳鉗口座壓板螺釘） 1件
5、支座調校器 1只
6、試樣對中器 1只
7、拆卸器（換擺用） 1件
8、地 腳 螺 釘 4個
9、調整斜鐵 4塊
10、防護網 1套
七、環境與工作條件
1、室溫10℃-35℃范圍內;相對濕度不大于80%；
2、周圍無振動、無腐蝕性介質和無較強電磁場干擾的清潔環境中；
3、電源電壓的波動范圍應在額定電壓的土10%以內；
4、在穩固的基礎上正確安裝。
BJJB-300B metal semi-automatic impact testing machine.
I. equipment name: metal semi-automatic impact testing machine.
Ii. Type no. : bjjb-300b.
Iii. Performance description:
The bjjb-300b impact tester is used to determine the resistance of metal materials under dynamic loads to determine the quality of materials under dynamic load.
This machine is semi-automatic control testing machine, the operation is simple and high efficiency, Yang pendulum is, impact, control, and can use the surplus energy of thrust sample after automatic Yang place ready for the next test, especially for continuous do impact test impact test lab and a lot of metallurgy, machinery manufacturing and other industries.
The bjjb-300b impact testing machine is in conformity with GB/ t3808-2002 "test of pendulum impact testing machine", and the impact test of metal materials is carried out according to GB/ t229-2007 "metal materials charpy impact test method".
Iv. Technical features:
1. The main engine of the testing machine is single supported column structure, cantilevered hanging pendulum mode, and swing hammer body U type;
2. The impact knife is fixed with screws and easy to replace;
3. Simple support beam support;
4. The main engine is equipped with safety protection pin and equipped with safety net;
5, testing machine is semi-automatic control, Yang place, hanging pendulum, the shock, put the pendulum are electrical control, and can use the surplus energy of thrust sample after automatic Yang pendulum is ready for the next test, especially for continuous do impact test impact test lab and a lot of metallurgy, machinery manufacturing and other departments;
6. The testing machine is in conformity with GB/ t3803-2002 "test of pendulum impact test machine" and the impact test of metal materials is carried out according to GB/ t229-2007 "metal summer gap impact test method".
V. technical indicators:
1. Impact energy: 300J (sledgehammer) 150 (small hammer)
2. Impact velocity: 5.2m/s.
3, pendulum Yang Angle: 150 °
4. Span of sample support: 40mm.
5. Round Angle of support clamps: R1.0~1.5mm.
6. Impact blade rounded Angle: R2.0~2.5mm R8mm.
7. Pendulum center to impact point distance: 750mm.
8. Standard sample size: 10 x 10(7.5 or 5) x 55mm.
9. Pendulum moment: M=160.7695N.m 80.3848n.m.
10. Power and power: three-phase four-wire 50Hz 380V 180W.
11. Dimensions: about 2100 x 650 x 1900mm.
12, the accuracy of Angle: 0.1 °
13. Weight: about 500Kg.
Vi. Main equipment configuration:
1. 300 joules host 1.
2, 150J, 300J pendulum each one.
3. Motor (mounted on the main machine);1
4. The Allen wrench S=12 (wrench socket screw) 1 piece.
5. Support adjustment device 1.
6. Sample pairs 1 only.
7. Disassembly (replace the pendulum) 1 piece.
8. Four screw pins.
9. Adjust the oblique iron 4 pieces.
10. Protective screen 1 set.
Environment and working conditions.
1, room temperature is 10 ℃ to 35 ℃ range;The relative humidity is not greater than 80%;
2. No vibration, no corrosive medium and clean environment without strong electromagnetic interference;
3. The fluctuation range of the power supply voltage shall be within 10% of the rated voltage;
4. Install correctly on solid foundation.
